PARTS THAT VINCENT NEVER MADE



PR50B/1assy - Comet Folding Kickstart Crank Assembly- $275 with UNPLATED Kicker Crank and all attaching parts. A few left.

The complete assembly: with unplated Kickstart Crank. F72/6 cadmium plated Footpiece, FT84 bolt, FT99 spring, #92 washer, #662 screw, PR3 rubber, FT202 plug, and 796 washer.

PR50B/1 - Comet Folding Kickstart Crank, Crank only- $180, UNPLATED. A few left.

THIS KICKSTART WAS NEVER MADE BY VINCENT. It's a modification of a Burman swivel Kickstart Crank that uses the cadmium plated F72/6 Twin Footpiece.

Much more substantial than OEM and will not fail. 4140 chromoly steel, heat treated to Rockwell 40C.



F24/1.5 - SERIES A PROP STAND, EXTENDED 1 1/2"- $125

New version has a 5/8" steel hole with a 1/2" ID hard bronze bushing installed. Can be used with a 5/8" (remove bushing), 9/16" (drill out bushing), or a 1/2" mounting shaft.

1 1/2" longer to achieve proper lean angle. Shown on left is a stock original.

The extended B and C Propstands, too.

Heat treated 4140 chromoly steel to Rockwell 40C.



F52/13F - COMET FOOTREST HANGER, FOLDING, Right- $140

Cadmium plated. Heat Treated 4140 chromoly to Rockwell 40C.

To be used with F72/1 Footrest.



F52/14F - COMET FOOTREST HANGER, FOLDING, Left- $140

To be used with F72 Footrest and original Comet Brake Cable.

Cadmium plated. Heat Treated 4140 chromoly to Rockwell 40C.



F72/7RL - EXTENDED FOOTREST, LEFT, 90 degree bends- $60

TWINS ONLY.

Can be used as the rider Left Hand Footrest for a more comfortable riding position.

Note that the riders foot is farther outboard causing more reach to the brake pedal.

Cadmium plated, 4140 Chromoly Steel, heat treated to 40 Rockwell C.



F72/8RR - EXTENDED FOOTREST, RIGHT, 90 degree bends- $60

TWINS ONLY.

Can be used as the rider Right Hand Footrest for a more comfortable riding position.

Note that the riders foot is farther outboard causing more reach to the Gear Pedal Footpiece.

Cadmium plated, 4140 Chromoly Steel, heat treated to 40 Rockwell C.



G108/2 - GEAR LEVER ARM- STEEL -$70

Ever have one break on a Road Run and even though you found a good aluminum welder, it still broke again? This heat treated 4140 chromly steel lever will not break, no need to carry a spare. Serrations are crisp. C & D Vincent Twins. Raised characters: G108/2 part number and circle SA forging mark as per original parts. Cadmium plated. Easily chromed, ask them not to remove raised characters.



FIREFLY - 1" Belt Buckle - Nickel Plated Steel - $35

For 1 inch wide belts.

Emblem made from the stamped aluminum Firefly cover.



FT130/HRD - KNOB NUT, HRD - Nickle Plated Steel - $30

Heat Treated 4140 chromoly steel to Rockwell 40C.

1/4" BSF, HRD in 3/16" letters, Magneto Cowl and Rear Fender Hinge Bolt. Battery hold down.



FT130/VIN - KNOB NUT, VINCENT - Nickle Plated Steel - $30

Heat Treated 4140 chromoly steel to Rockwell 40C.

1/4" BSF, VINCENT in 3/32" letters, Magneto Cowl and Rear Fender Hinge Bolt. Battery hold down.